HG Marble Wash & Shine

HG marble wash & shine leaves minuscule acrylic balls behind on the surface. This protects the marble surface and any applications of HG marble shine finish against scratching. The surface gets a new gloss at the same time. Add one cup full of HG marble wash & shine cleaner per litre of lukewarm water. Mop the floor. It is not necessary to rinse off or dry the floor afterwards.

HG Oil & Grease Absorber

Stains which appear in porous material are often difficult to remove. HG oil & grease absorber however draws out unsightly oil or grease stains from floors, tabletops and walls. The product is so effective that it removes even the most stubborn stains. It can be applied on all porous stone surfaces including flagstones, terra cotta, marble, limestone and other types of natural stone as well as cement, concrete and paving slabs. HG oil & grease stain absorber is self-acting meaning that there is no need for brushing or scrubbing. Stir HG oil & grease absorber well before use. Then apply a 1/2 cm thick layer on the stain with a spoon or palette knife. After HG oil & grease stain absorber is entirely absorbed it forms a cake which is easy to remove. Take of this cake and anything left on the surface with a damp cloth.

3 HG Marble Cement & Lime Film Remover

HG marble cement & lime film remover removes cement film and lime scale from marble and other sorts of calcareous of natural stone such as travertine, granite, terrazzo and ashlar. Dilute HG marble cement and lime film remover in water. Then apply with a scrubbing brush. Allow a few minutes for the product to work, scrub well and rinse off with water. One litre is enough for a floor surface area of 40 to 50 m².

HG Marble Stripper

HG marble stripper is a powerful cleaner for the removal of HG marble shine finish and stubborn dirt and grease. Dilute HG marble stripper in 1 litre of lukewarm water. Then apply with a scrubbing-brush. Allow a few minutes for the product to work, scrub well and rinse off with water. One litre is enough for a surface area of 15 m².

HG Super Remover

HG super remover for tiled floors and natural stone floors is a professional cleaner, extremely effective for really stubborn contamination, such as persistent layers of polish, old layers of polish or heavily ingrained dirt in passageways, etc. Dilute HG super remover, 1 part cleaner to 10 parts water. For very stubborn contamination the dilution can be reduced to 1 part cleaner to 4 parts water. Using a brush or a mop, for example, apply the solution to the area that is to be cleaned. Then, thoroughly scrub the surface. If necessary, an electrical scrubbing machine can be used. After a delay of a few minutes, to allow the cleaner to penetrate, repeat the scrubbing. Then, using a floor-cloth, wash the remover from the cleaned surface. Frequently rinse and wring-out the floor-cloth. Finally, rinse, twice using clean water. 1 Litre of HG super remover is sufficient to clean 35 to 70 m², depending on the degree of pollution.

HG Permanent anti-slip

HG permanent anti-slip creates a safe grip-surface on smooth tiles and natural stonework used for (floor) surfaces and, also, in showers and baths with enamel or ceramic surfaces. Starting from now, you no longer need to be afraid of slipping in the bathroom, on the stairs, in the entrance hall, etc. HG permanent anti-slip is suitable for use indoors and outdoors. Using HG polish, wax and dirt remover, thoroughly clean the surface that is to be treated, removing all dirt and grease. If the surface is marble, use HG marble shine finish remover. Rinse the surface perfectly clean, with water and, using a sponge or water vacuum cleaner, remove all remaining water. Allow the surface to dry. Ensure that the surface that is to be treated with HG permanent anti-slip is carefully isolated from other parts of the base-material, so that the coating remains intact on the area that is being treated. A good way to do this is to apply 2 layers of masking tape round the perimeter of the area that is to be treated.

HG Marble Stain Color Remover

HG marble stain color remover easily removes all kinds of colored liquid stains such as coffee, tea, fizzy drink and red wine stains from marble, travertine or terrazzo. Remove oil and grease stains with HG spot stain remover. Spray the surface well. Allow at least 10 minutes for the product to work. Then remove with a sponge or cloth and hot water.

HG Marble Impregnator

HG marble impregnator penetrates deep into the surface and completely seals off small pores. Larger pores are made smaller meaning liquid molecules can no longer be absorbed. However, any dampness in the floor can still evaporate. It is suitable for inside and outside use. Apply HG marble impregnator evenly in one direction with a paint roller or a non fluffy cloth. Allow to penetrate for a maximum of 5 minutes. Then remove any surplus with a dry cloth. One litre is enough for a surface area of 10 to 20 m².

HG Stain Protector

HG stain protector is for use on unglazed ceramic tiles, percellanato, glazed stone stonewear, slate, marble, granite and other sorts of natural stonework. It provides protection against almost all water-based spillages - such as those made by wine, cola, etc.- and against oily spots and general contamination. As the porous based materials are protected deep within the pores HG stain protector is suitable for use in the living room, kitchen and bathroom.First thoroughly clean the surface that is to be treated. Ceramic tiles, granite, slate etc. should be cleaned with HG polish, wax and dirt remover. Marble and grades of limestone should be cleaned with HG marble shine finish remover. Unpolished floor tiles, such as for example polished stone wear and porcellanato should be cleaned with HG porcelain cleaner. Using a brush or a roller, apply a liberal coating of HG stain protector. It is recommended that very porous base materials are treated a second time. 1 litre of HG stain protector is sufficient for 100 m². All HG maintenance products for the base materials can be used as normal.

HG Marble Shine Finish

HG marble shine finish provides a thin protective coating. This means that the pores are completely sealed. Dirt does not stand a chance. It also prevents damage caused by fruit juice for example. The result is a deepening of the color and a lovely shining finish. Dilute HG marble shine finish in 1 litre of water. Then apply with a clean, non fluffy cloth wrapped around a floor wiper. Spread evenly in one direction. Now wait 45 minutes. Apply the second coat at right angles of the first. One litre is enough for a surface area of 60 m².

HG Marble Crystallizer

Fizzy drinks or fruit juice for example can damage marble and result in a it becoming dulled. HG marble crystallizer restores the shine on such an areas. Apply HG marble crystallizer with a cloth onto the surface and buff this in with the steel wool pad attached to the bottle. Keep buffing until a deep gloss appears.